Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC2002ELDORADO V8-4.6L VIN YREPAIR AND DIAGNOSISTRANSMISSION AND DRIVETRAINAUTOMATIC TRANSMISSION/TRANSAXLESHIFT INTERLOCKTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESSCAN TOOL DATA DEFINITIONS
2002 Cadillac Eldorado V8-4.6L VIN Y
Scan Tool Data Definitions
2002 Cadillac Eldorado V8-4.6L VIN YSECTION Scan Tool Data Definitions
Scan Tool Data Definitions
Body Control Module (BCM)
Battery Voltage: Displays 0.0 - 25.5 V. This parameter is the system voltage measured by the PZM at the PZM battery input.
Park Relay: Displays indicates ON when the body control module applies the ground to the Park Relay control circuit.
Powertrain Control Module (PCM)
Ignition Voltage: Displays 0.0 - 25.5 V. This parameter is the system voltage measured by the PCM at the PCM ignition input when the ignition switch is in the RUN position.
IMS (Transmission Internal Mode Switch) Range: Displays Park, Park/Reverse, Reverse, Reverse/Neutral, Neutral, Neutral/Drive 4, Drive 4, Drive 4/Drive 3, Drive 3, Drive 3/Drive 2, Drive 2, Drive 2/Drive 1, Drive 1, Invalid or Open. The IMS Range display represents a decoded status of the four inputs from the IMS. This range includes all possible in-between gear states as well as the detent gear states. The combination of IMS inputs to the PCM are used by the PCM in order to determine what position the manual valve is in at any time.
IMS (Internal Mode Switch) States A/B/C/P: Displays LOW or HI for the state of each of the four inputs from the IMS. LOW displayed indicates a low voltage signal (0 volts) being monitored at the PCM. HI displayed indicates a high voltage signal (B+) being monitored at the PCM.
Body Control Module (BCM)
Battery Voltage: Displays 0.0 - 25.5 V. This parameter is the system voltage measured by the PZM at the PZM battery input.
Park Relay: Displays indicates ON when the body control module applies the ground to the Park Relay control circuit.
Powertrain Control Module (PCM)
Ignition Voltage: Displays 0.0 - 25.5 V. This parameter is the system voltage measured by the PCM at the PCM ignition input when the ignition switch is in the RUN position.
IMS (Transmission Internal Mode Switch) Range: Displays Park, Park/Reverse, Reverse, Reverse/Neutral, Neutral, Neutral/Drive 4, Drive 4, Drive 4/Drive 3, Drive 3, Drive 3/Drive 2, Drive 2, Drive 2/Drive 1, Drive 1, Invalid or Open. The IMS Range display represents a decoded status of the four inputs from the IMS. This range includes all possible in-between gear states as well as the detent gear states. The combination of IMS inputs to the PCM are used by the PCM in order to determine what position the manual valve is in at any time.
IMS (Internal Mode Switch) States A/B/C/P: Displays LOW or HI for the state of each of the four inputs from the IMS. LOW displayed indicates a low voltage signal (0 volts) being monitored at the PCM. HI displayed indicates a high voltage signal (B+) being monitored at the PCM.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.