Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCADILLAC1999SEVILLE SLS V8-4.6L VIN YREPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - CRUISE CONTROLCRUISE CONTROL MODULESERVICE AND REPAIR
1999 Cadillac Seville SLS V8-4.6L VIN Y
Cruise Control Module: Service and Repair
1999 Cadillac Seville SLS V8-4.6L VIN YSECTION Service and Repair
REMOVAL PROCEDURE
1. Remove the cruise control cable (3) at the engine bracket and the throttle body cam.
2. Remove the cruise control cable (1) from the module assembly connector (3).
3. Disconnect the electrical connector from the module assembly.
4. Remove the nuts (2) from the mounting studs.
5. Remove the fasteners (3) retaining the cruise control module mounting bracket (2) to the cruise control module (1).
Remove the cruise control module bracket (2) from the module (1).
INSTALLATION PROCEDURE
1. Install the cruise control module (1) to the bracket (2).
NOTE: Refer to Fastener Notice in Cautions and Notices.
2. Install the module to bracket fasteners (3).
Tighten
Tighten the fasteners to 7.5 N.m (66 lb in).
3. Install cruise control module (1) onto the studs on the cowl.
4. Install the two nuts (2).
Tighten
Tighten the bracket retaining nuts to 9 N.m (80 lb in).
5. Connect the electrical connector to the module.
6. Install the cruise control cable (1) to the module assembly connector (3).
7. Install the cruise control cable (3) to the engine bracket and the throttle body cam.
8. Adjust the cruise control cable.
1. Remove the cruise control cable (3) at the engine bracket and the throttle body cam.
2. Remove the cruise control cable (1) from the module assembly connector (3).
3. Disconnect the electrical connector from the module assembly.
4. Remove the nuts (2) from the mounting studs.
5. Remove the fasteners (3) retaining the cruise control module mounting bracket (2) to the cruise control module (1).
Remove the cruise control module bracket (2) from the module (1).
INSTALLATION PROCEDURE
1. Install the cruise control module (1) to the bracket (2).
NOTE: Refer to Fastener Notice in Cautions and Notices.
2. Install the module to bracket fasteners (3).
Tighten
Tighten the fasteners to 7.5 N.m (66 lb in).
3. Install cruise control module (1) onto the studs on the cowl.
4. Install the two nuts (2).
Tighten
Tighten the bracket retaining nuts to 9 N.m (80 lb in).
5. Connect the electrical connector to the module.
6. Install the cruise control cable (1) to the module assembly connector (3).
7. Install the cruise control cable (3) to the engine bracket and the throttle body cam.
8. Adjust the cruise control cable.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.