Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSBMW2011128I CONVERTIBLE (E88) L6-3.0L (N51)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTECHNICAL SERVICE BULLETINS
2011 BMW 128i Convertible (E88) L6-3.0L (N51)
Computers and Control Systems: Technical Service Bulletins
2011 BMW 128i Convertible (E88) L6-3.0L (N51)SECTION Technical Service Bulletins
- Customer Interest
- Engine Controls - Camshaft Position/VANOS DTC's, MIL ON
- Computer/Controls - Idle Fluctuation During Warm-up Phase
- Computer/Controls - MIL ON And DTC's 2F99, 10B008 Stored
- Fuel System - MIL ON Or Check Gas Cap Is Illuminated
- Engine Controls - DTC 2A1A/MIL ON While Driving
- Audio System - SIRIUS(R) Stations Not In Channels List
- Computers/Controls - JBE Fails Programming
- Engine Controls - MIL ON/Codes 2ADA/2ADB Set
- Engine Controls - 2AD8 EAC Sensor Code Stored/MIL ON
- Emissions - MIL ON And DTC FC 2A17 Stored
- Fuel System - No Start and or False Fuel Gauge Reading
- Computer/Controls - 'Electronic Malfunction' Displayed
- Navigation System - Vehicle Position Missing/Incorrect
- By Symptom
- Customer Interest
- Engine Controls - Camshaft Position/VANOS DTC's, MIL ON
- Computer/Controls - Idle Fluctuation During Warm-up Phase
- Computer/Controls - MIL ON And DTC's 2F99, 10B008 Stored
- Fuel System - MIL ON Or Check Gas Cap Is Illuminated
- Engine Controls - DTC 2A1A/MIL ON While Driving
- Audio System - SIRIUS(R) Stations Not In Channels List
- Computers/Controls - JBE Fails Programming
- Engine Controls - MIL ON/Codes 2ADA/2ADB Set
- Engine Controls - 2AD8 EAC Sensor Code Stored/MIL ON
- Emissions - MIL ON And DTC FC 2A17 Stored
- Fuel System - No Start and or False Fuel Gauge Reading
- Computer/Controls - 'Electronic Malfunction' Displayed
- Navigation System - Vehicle Position Missing/Incorrect
- Driveability
- Erratic Operation
- False instrument warning light/gauges
- Inoperative
- Starting problems
- Customer Interest
- All Technical Service Bulletins
- Engine Controls - Camshaft Position/VANOS DTC's, MIL ON
- Fuel System - Fuel Pressure Control Test Plan Error
- Computer/Controls - Idle Fluctuation During Warm-up Phase
- Computer/Controls - MIL ON And DTC's 2F99, 10B008 Stored
- Computers, Controls - Programming VS Veh. Data Status
- Fuel System - MIL ON Or Check Gas Cap Is Illuminated
- Engine Controls - DTC 2A1A/MIL ON While Driving
- Audio System - SIRIUS(R) Stations Not In Channels List
- Computers/Controls - JBE Fails Programming
- Engine Controls - MIL ON/Code 29DA set
- Compuetrs/Controls - Recommended Diagnostic Procedures
- Engine Controls - MIL ON/Codes 2ADA/2ADB Set
- Engine Controls - 2AD8 EAC Sensor Code Stored/MIL ON
- Emissions - MIL ON And DTC FC 2A17 Stored
- Computers/Controls - MIL ON, No DTC, DMTL Test Plan INOP
- Fuel System - No Start and or False Fuel Gauge Reading
- Computer/Controls - 'Electronic Malfunction' Displayed
- Navigation System - Vehicle Position Missing/Incorrect
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.