Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2012S4 QUATTRO SEDAN (8K2) V6-3.0L SC (CCBA)REPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - BODY AND FRAMEPOWER SEAT CONTROL MODULESERVICE AND REPAIRPOWER STANDARD FRONT SEATS WITH OR WITHOUT MEMORY FUNCTIONRIGHT FRONT SEAT VENTILATION CONTROL MODULE (SEAT HEATER INTEGRATED) (J799)/(J800)
2012 Audi S4 Quattro Sedan (8K2) V6-3.0L SC (CCBA)
Right Front Seat Ventilation Control Module (Seat Heater Integrated) (J799)/(J800)
2012 Audi S4 Quattro Sedan (8K2) V6-3.0L SC (CCBA)SECTION Right Front Seat Ventilation Control Module (Seat Heater Integrated) (J799)/(J800)
Right Front Seat Ventilation Control Module (Seat Heater Integrated) (J799)/(J800)
Special tools, testers and auxiliary items required
• Trim Removal Wedge (3409)
Removing
• Follow all safety precautions when working on pyrotechnic components.
• Before handling pyrotechnical components (for example, disconnecting the connector), the person handling them must discharge static electricity. For example, by briefly touching the door striker pin.
- Turn on the ignition.
- Disconnect the battery ground cable from the battery with the ignition on.
- Remove the front seat:
• Standard seat and Sport seat (manual). Refer to => [ Manual Standard Front Seat ] Manual Standard Front Seat.
- Attach the front seat to the (VAS 6136) => [ Front Seats, Installing on the ] Front Seats, Installing on the Fixture For Seat Repair (VAS 6136).
- Disconnect the connector - 2 - right front seat ventilation control module (J799) / (J800) - 1 - by pressing the release - arrow -.
- Release the retaining strap - arrow 1 - using the (3409).
- Pivot the control module downward - arrow 2 -.
- Release the tab on the control module - arrow 3 - on the mount.
- Remove the control module.
Installing
• Follow all safety precautions when working on pyrotechnic components.
• Before handling pyrotechnical components (for example, connecting electrical connector), the person handling them must discharge static electricity. For example, by briefly touching the door striker pin.
Install in reverse order of removal. Note the following:
• Make sure the memory seat adjustment control module engages audibly in the retainer.
• Make sure the connectors are installed all the way in and are secure.
Connect the battery with the ignition switched on. Pyrotechnic components could deploy after connecting the battery if they were not repaired correctly. Individuals must not be inside the vehicle when connecting the battery.
- Connect the battery ground cable with the ignition turned on.
• If the airbag indicator lamp (K75) indicates a fault after installation, the DTC memory must be checked, deleted and checked again using the Vehicle Diagnostic Tester.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.