Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSAUDI2006A4 QUATTRO SEDAN (8EC) V6-3.2L (BKH)REPAIR AND DIAGNOSISHEATING AND AIR CONDITIONINGTESTING AND INSPECTIONSCAN TOOL TESTING AND PROCEDURESMEASURED VALUE BLOCK, READING
2006 Audi A4 Quattro Sedan (8EC) V6-3.2L (BKH)
Measured Value Block, Reading
2006 Audi A4 Quattro Sedan (8EC) V6-3.2L (BKH)SECTION Measured Value Block, Reading
Measured Value Block, Reading
• To check the speed signal after the ignition is switched on, drive the vehicle several meters at least at a walking pace (more than 5 km/h).
• Installation locations of activated components => [ A/C System Control and Regulation Components ] A/C System Control and Regulation Components.
- With the ignition switched off, connect the Vehicle Diagnosis, Testing and Information System (VAS 5051A) e.g. with the diagnostic cable (VAS 5051/5A) and the K-wire adapter (VAS 6017B) (or the K-wire adapter (VAS 6017A)) to the 16-pin data link connector (DLC) => [ VAS 5051A, Connecting and Selecting Functions ] VAS 5051A, Connecting and Selecting Functions.
- Switch on ignition or start engine.
- Set operating mode "Auto" on A/C control head Climatronic Control Module (J255).
- Select Address word "08" for A/C heater/electronics => [ VAS 5051A, Connecting and Selecting Functions ] VAS 5051A, Connecting and Selecting Functions.
Indication on display of Vehicle Diagnosis, Testing and Information System (VAS 5051A):
- Check DTC memory => [ DTC Memory, Interrogating ] DTC Memory, Interrogating.
- Select function "08 - Read Measuring Value Block".
Indication on display of Vehicle Diagnosis, Testing and Information System (VAS 5051A):
• Display field - 1 - indicates request to input display group.
• Display field - 2 - shows input keyboard.
- Via the input keyboard in display field - 2 -, enter the desired display group (e.g. "01" or "001" for " display group number 001") => [ Display Group Overview ] Display Group Overview and confirm by pressing the Q button.
Indication on display of Vehicle Diagnosis, Testing and Information System (VAS 5051A):
• Display field - 1 - shows the display group selected.
• Display field - 2 - displays the values of the four display fields:
- Value for display field "1" is displayed in the first row.
- Values for respective display zones appear on second, third and fourth lines.
- If no display appears in this row, a display field is not assigned.
• Pressing button - 3 - changes to a different display group.
• Press button - 4 - to change to a different function (e.g. from "Read Measuring Value Block" to "Basic Setting " and back again).
- Input the display group number (overview) => [ Display Group Overview ] Display Group Overview.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.