⚙️Serpentine Belt
Mitsubishi Diamante Serpentine Belt
Find serpentine belt routing diagrams, part numbers, and replacement instructions for your Mitsubishi Diamante. All years covered.
Quick Answer
The Mitsubishi Diamante serpentine belt routes around the alternator, power steering pump, A/C compressor, and water pump. Belt length and routing vary by engine — see diagrams below.
1999-2004
1999-2004Belt TypeMulti-rib serpentine (6PK or 7PK)
Belt Length85" - 100" (varies by engine and A/C option)
Tensioner TypeManual adjustment bolt or automatic
Replacement Interval60,000 - 100,000 miles
Notes
- →Take a photo of the belt routing BEFORE removing the old belt
- →Check if your model uses automatic or manual tensioner adjustment
- →Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
- →A new belt may squeal briefly at startup — this usually stops within a few minutes
1993-1998
1993-1998Belt TypeMulti-rib serpentine (6PK or 7PK)
Belt Length85" - 100" (varies by engine and A/C option)
Tensioner TypeManual adjustment bolt or automatic
Replacement Interval60,000 - 100,000 miles
Notes
- →Take a photo of the belt routing BEFORE removing the old belt
- →Check if your model uses automatic or manual tensioner adjustment
- →Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
- →A new belt may squeal briefly at startup — this usually stops within a few minutes
1992-1992
1992-1992Belt TypeMulti-rib serpentine (6PK or 7PK)
Belt Length85" - 100" (varies by engine and A/C option)
Tensioner TypeManual adjustment bolt or automatic
Replacement Interval60,000 - 100,000 miles
Notes
- →Take a photo of the belt routing BEFORE removing the old belt
- →Check if your model uses automatic or manual tensioner adjustment
- →Inspect the tensioner pulley and idler pulleys for bearing noise while the belt is off
- →A new belt may squeal briefly at startup — this usually stops within a few minutes
Frequently Asked Questions
- How do I replace the serpentine belt on a Mitsubishi Diamante?
- Release tension on the automatic tensioner with a breaker bar, slide the old belt off, route the new belt per the diagram (usually on a sticker under the hood), and release the tensioner onto the new belt. The job takes 15-30 minutes.
- How do I know if my Mitsubishi Diamante serpentine belt needs replacing?
- Signs include squealing at startup, visible cracks or fraying on the belt, loss of power steering or A/C, and the battery light coming on. Most belts should be replaced every 60,000-100,000 miles.
- What happens if the serpentine belt breaks on my Mitsubishi Diamante?
- If the serpentine belt breaks, you lose power steering, alternator charging, A/C, and (on some engines) the water pump. Pull over immediately — driving without the water pump will cause overheating and engine damage.
- Where is the belt routing diagram on a Mitsubishi Diamante?
- Most Mitsubishi Diamante models have a belt routing diagram on a sticker under the hood, near the radiator support or on the inner fender. If it's missing, check the service manual or see the diagrams below.
Mitsubishi Diamante Repair Guides
More Mitsubishi Diamante Guides
Browse all Serpentine Belt pages →🔋Mitsubishi Diamante Battery Location❄️Mitsubishi Diamante Coolant Type🧪Mitsubishi Diamante Fluid Capacities💡Mitsubishi Diamante Headlight Bulb Size🛢️Mitsubishi Diamante Oil Type & Capacity⚡Mitsubishi Diamante Spark Plug Type⚙️Toyota 4Runner Serpentine Belt⚙️Toyota Avalon Serpentine Belt⚙️Toyota Camry Serpentine Belt⚙️Toyota Celica Serpentine Belt⚙️Toyota Corolla Serpentine Belt⚙️Toyota Echo Serpentine Belt⚙️Toyota Highlander Serpentine Belt⚙️Toyota Land Cruiser Serpentine Belt⚙️Toyota Matrix Serpentine Belt